Construction Systems Supply - Epoxy and Coating Supplier

Epoxy coating for concrete

These Eco-Polymer 100% solids hybrid Novolac coatings offer outstanding chemical resistance and excellent adhesion (in excess of 3000 psi). These epoxy products provide great impact resistance and bridge microfractures in concrete. Many are available with Kevlar reinforcement and ceramic for increased wear resistance.

The following Eco-Polymer epoxies provide outstanding chemical resistance and adhesion on wet, corroded surfaces as well as low-temperature application and cure environments. Effective against salts, alkalies, sewage, and dilute mineral acids, these solutions are ideal for concrete and metal in aqueous service in water/waste management and may be applied underwater.

Example applications for concrete epoxy coatings:

Products List:

SC-1100 Fast Set is a 100% solids low viscosity primer designed for sealing concrete. Its fast cure rate makes it ideal for cold weather applications. SC-1100 Fast Set is a 100% solids, low viscosity hybrid novolac epoxy primer designed for deep penetration and sealing of concrete surfaces. SC-1100 Fast Set helps eliminate outgassing and bubbles. SC-1100 Fast Set can be applied to green concrete as young as seven days based on ASTM F1869-10 with a moisture vapor emission of <10lbs.

Eco-Polymer Protective Coatings consistently produces products of exceptional chemistry delivering the best in corrosion protection, while being safe for our environment and totally user friendly. SC-3300 is 100% solids, sprayable, industrial maintenance coating for metal and concrete substrates. SC-3300 is a high cross-link density; ceramic-filled novolac coating that is designed to provide superior, long-term chemical resistance and good immersion service. The solids content and morphology make SC-3300 an excellent tank liner.

Eco-Polymer Protective Coatings consistently produces products of exceptional chemistry delivering the best in corrosion protection, while being safe for our environment and totally user friendly.SC-5400 ia a 100% solids novolac coating designed for maximum heat and chemical resistance. Excellent coating for floors, secondary containment, ducts, piping, vessels, and storage tanks. Withstands up to 98% sulfuric acid, 100% phosphoric acid, 35% nitric acid, 100% hydrofluoric acid, MEK, mineral acids, bleach, chlorides, potassium and sodium. SC-5400 is a true high performance coating.

SC5600 is a 100% solids unique high performance novalac coating system for long term chemical exposure in tank linings, equipment coating and secondary containment areas. It is a cross-linked ceramic filled liner coating designed to withstand elevated temperatures and maximum chemical resistance Bond strength is unsurpassed; it provides excellent wear and is self priming to metal surfaces. Suitable for both metal & concrete protection.

This water-based concrete penetrating sealer is specially formulated to waterproof, damp proof, seal, and keep the natural appearance and profile of Portland cement-based concrete, concrete blocks, mortar, gunnite, slabs, floors, subsurface vaults, basements, walls, roofs, pillars, pipe, sculpture, architectural structures, and statuary. Use Crystal Lok on concrete in any location where the seepage is not caused by cracking or other structural flaws.

BH705M is a two-component elastomeric compound of asphalt and polymers formulated for mixing and spraying at ambient temperature. It cures (by an in situ chemical reaction) to a tough, abrasive-resistant film which shows almost 100% elastomeric recovery from mechanical stress. BH705M is used as a waterproof coating over insulation as an excellent barrier against weather and moisture vapor. It has excellent adhesion to insulation, metal, and other substrates and, due to its unusually low temperature properties, is ideal for use in extremely cold environments. On concrete and masonry, 705M may be used as a moisture-vapor barrier coating above and below grade. It will protect metals and wood against corrosion by acids, alkalis, salts, and moisture. 705M is resistant to ultraviolet degradation from long term exposure to sunlight. BH705M can also be used to cement pre-formed insulation to piping or vessels and to adhere blocks of insulation together. It is especially recommended where movement of insulation will be encountered.

SP-2000R is comprised of 100% solids and contains no VOC’s. Excellent adhesion properties allow SP-2000R to bond on steel, concrete and iron even when coating conditions are less than ideal. The R in SP-2000R represents the incorporation of re-cycled tire rubber. Using the re-cycled tire rubber has a dual purpose. First, the rubber enhances the product with excellent impact resistance. Second, it serves the environment by providing a useful application for what otherwise fill landfills. SP-2000R can be used on a variety of substrates and applications. Typical applications include wastewater (tanks, lift stations, wet wells, and manholes), cooling towers, and more. SP-2000R can also be used as an interior or exterior pipe lining or coating. Primers recommended on concrete.

SC-3000M is 100% solids, spray able, industrial maintenance coating for metal and concrete substrates. SC-3000M is a high cross-link density; ceramic-filled novolac coating that is designed to provide superior, long-term chemical resistance and good immersion service. The solids content and morphology make SC-3000M an excellent tank liner.

EcoPolymer SP-2000W is NSF/ANSI 61 certified for drinking water and with FDA 21CFR175.300 for direct and indirect contact with food. It is certifi ed for commercial hot and cold water tanks. Wherever potable water and food is stored or piped, SP-2000W is the coating to use. Because SP-2000W is 100% solids, it contains no volatile organic compounds or solvents, it maybe safely applied in confined areas with good ventilation. EcoPolymer’s SP-2000W has been a leader in hybrid novolac coating technology and since 1990 is a standard for lining ductile pipe used in sewage gathering systems. Throughout wastewater transportation and treatment plants, EcoPolymer can be found protecting steel, ductile and concrete substrates.